• Home
  • Perle S-1110-S2LC10-XT 10/100/1000 PoE/ PoE+ Media Converter

Perle S-1110-S2LC10-XT 10/100/1000 PoE/ PoE+ Media Converter

SKU: 05090720
05090720
£750.00 (Ex VAT)
(0) No Reviews yet

This item is IN STOCK

Perle PoE Media Converters are classified as Power Sourcing Equipment (PSE). While using standard UTP cables that carry Ethernet data, Perle PoE media converters can also provide power to one or two Powered Devices (PDs). Perle has PoE media converter models that support the IEEE 802.3af PoE standard (15.4W of power) or the IEEE 802.3at PoE+ standard (30W of power). Learn more about PoE.

Perle 10/100/1000 PoE Ethernet to FibrE Converters provide an economical path to extend the distance of an existing network with fibrE cabling. At the same time they function as PoE injectors to power devices like IP phones, video conferencing equipment, IP cameras and Wi-Fi devices over copper UTP cabling.

Multi-port PoE media converters enable a variety of flexible network designs. They can feature single or dual RJ-45 ports to power one or two PD’s per converter and single or dual fibre ports.

Network Administrators can "see-everything" with Perle's advanced features such as Auto-Negotiation, Auto-MDIX, Link Pass-Through, Fibre Fault Alert, and Loopback. This allows for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle's Gigabit rate converting PoE Media Converters the smart choice for IT professionals.

Power Over Ethernet

Performs the Power Sourcing Equipment (PSE) function on 1 or 2 UTP ports for IEEE 802.3af (15.4 watts PoE) and IEEE 802.3at (up to 30 watts PoE+) compliant devices. Available in PoE and PoE+ models. PoE+ models support both Type 1 (PoE) and Type 2 (PoE+) PD gear.

Advanced Power Management

- Enable/Disable PSE power by UTP port

- PD signature detection

- Over-Current Protection

- PD power classification detection (Class 0,1,2,3,4)

PD Power Reset

Ideal for remotely resetting equipment, this configurable function performs a momentary power reset to the attached Powered Device (PD). When enabled, the media converter will, upon loss of fibre RX, turn off PSE output power supplied to the PD device for 2 seconds then turn the power back on and leave it on until such time that another fibre RX link is lost (after it was re-established). When disabled, a loss of fibre RX has no effect on PSE power to the PD device(s).

Powered Device Support

Support is included for a broad range of PD (Powered Devices)

- IEEE Standard PoE/PoE+ (Alternative A and B)

- Legacy High Capacitance PDs

- Legacy VoIP phones and Wireless Access Points

Multiport Configurations

- 2 port – 1 UTP and 1 fibre (fixed fibre or SFP slot )

- 3 port - 1 UTP and 2 SFP fibre slots or 2 UTP and 1 fibre (fixed fibre or SFP slot)

- 4 port - 2 UTP and 2 SFP fiber slots

Fibre Redundancy

When enabled on dual fibre models, the media converter treats Fibre 1 as the primary and if the link fails, the fibre link is switched over to fibre 2 within 50ms.

Redundant Primary Fibre

If the “Fibre Redundancy” feature is also enabled, the primary fibre 1 link is continuously monitored and if is restored for at least 6 seconds, the link will be switched back from the secondary fibre 2 port to the primary fibre 1 port.

Power Strain Relief Strap

Included with all models, a strain relief strap is provided to ensure a solid and secure power connection to the media converter. Ideal for areas that may be exposed to vibration.

SFP Speed Sensing

Automatically detects whether a Gigabit or Fast Ethernet fibre SFP has been inserted and adjusts accordingly.

Auto-Negotiation (802.3u)

The media converter supports auto negotiation. The 1000Base-X fibre interface negotiates according to 802.3 clause 37. The 10/100/1000Base-T negotiates according to 802.3 clause 28 and 40. The 1000Base-X will link up with its partner after the highest common denominator (HCD) is reached and the copper has linked up with its partner. The 1000Base-X will continue to cycle through negotiation transmitting a remote fault of offline (provided this is enabled through the switch setting) until the copper is linked up and the HCDs match. The media converter supports auto-negotiation of full duplex, half duplex, remote fault, full duplex pause, asymmetric pause and Auto MDI-X.

Auto-MDIX

Auto-MDIX (automatic medium-dependant interface crossover) detects the signalling on the copper Ethernet interface to determine the type of cable connected (straight-through or crossover) and automatically configures the connection when enabled. The media converter can also correct for wires swapped within a pair. The media converter will adjust for up to 120ns of delay skew between the 1000Base-T pairs.

Smart Link Pass-Through

When the Link Mode switch is placed into Smart Link Pass-Through mode, the copper Ethernet port will reflect the state of the 1000Base-X media converter port. This feature can be used whether fibre auto-negotiation is enabled or disabled.

Fibre Fault Alert

With Fibre Fault Alert the state of the 1000Base-X receiver is passed to the 1000Base-X transmitter. This provides fault notification to the partner device attached to the 1000Base-X interface of the media converter. If the 1000Base-X transmitter is off as a result of this fault it will be turned on periodically to allow the condition to clear should the partner device on the 1000Base-X be using a similar technique. This eliminates the possibility of lockouts that occur with some media converters. Applies only when fibre auto-negotiation is disabled.

Pause (IEEE 802.3xy)

Pause signalling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed. The media converter supports pause negotiation on the 10/100/1000Base-T connection and 1000Base-X fibre connection.

- With Autoneg on the device will advertise sym and asymmetric pause

- With Autoneg off – Pause receive and send will be disabled

Duplex

Full and half duplex operation supported.

Jumbo Packets

Transparent to jumbo packets up to 10KB.

VLAN

Transparent to VLAN tagged packets.

Remote Loopback

Capable of performing a loopback on the 1000Base-X fibre interface.

Operating Temperature0°C to 50°C
Power Requirement46 - 57v DC
Dimensions (mm)150 x 95 x 26

Ratings & Reviews

No reviews available

Be the first to Write a Review